Aqium® 3D – Scannable precision impression material
Hydrophilic
Hydrophilic – Tear strength – Ultimate elongation
With Aqium® 3D, a high level of hydrophilicity, with simultaneously high tensile strength and ultimate elongation, has been successfully achieved. In particular Aqium® 3D LIGHT, MEDIUM, and MONO provide an increased level of hydrophilicity. Usually these important mechanic specific values will be reduced more the higher the hydrophilic property is adjusted. Lower values cause a tear of the material during the removal out of the patient’s mouth and the impression must be repeated. Aqium® 3D offers safety herein and takes, in this combination, a leading position in the dental market.
The individual components are optimally co-ordinated with the others regarding the important hydrophilic properties, ultimate tensile strength, elongation of break, thixotropy and fluidity and thus render an incomparably high performance of the overall system.
Viscosities
With its extensive range of material types, the Aqium® 3D impression system meets all requirements of current impression techniques in terms of viscosity, consistency and Shore hardness.
The combinations listed as possibilities in the table on the left are recommendations from a specification perspective; further combinations are possible, of course. The high material quality of the Aqium® 3D products supports perfect impression taking in any case.
Recommendations Material Combination/ Impression technique
To enlarge the table please click…
Scannability
During the development of the Aqium® 3D the requirements of the progressive digital dentistry were taken in account. The impressions, which were taken in the conventional way with Aqium® 3D, are scannable without the addition of a powder or spray. In this way a computer-assisted production of tooth restorations, based on digital data, will be enabled, even if a scan directly in the mouth turns out to be problematic caused through difficult situation in the mouth.
It is not a mandatory to have a scanner in the dental practice. The impression is dimensionally stable and can be sent to a milling center or dental laboratory, who will carry out all further digital workflow for the production of the dental prosthesis.
range
Aqium® 3D PUTTY SOFT / DEFAULT
- Working time: 2 min. 15 sec.
- Time in mouth: 2 min. 15 sec.
- Colour: lilac-blue
Aqium® 3D PUTTY SOFT packing unit
- REF 88631 2x 300 ml boxes (catalyst + base)
- REF 85191 1x 380 ml cartridge 5:1 + 10 Mixing tips + 1 Fix cap
- REF 85131 2x 380 ml cartridges 5:1
Aqium® 3D PUTTY DEFAULT packing unit
- REF 88632 2x 300 ml boxes (catalyst + base)
Aqium® 3D HEAVY
- Working time: 2 min. 15 sec.
- Time in mouth: 2 min. 15 sec.
- Colour: lilac-blue
Aqium® 3D HEAVY packing unit
- REF 82533 2x 50 ml cartridges + 6 Mixing tips NT, green
- REF 85133 2x 380 ml cartridges 5:1
Aqium® 3D LIGHT
- Working time: 2 min. 15 sec.
- Time in mouth: 2 min. 15 sec.
- Colour: neon-yellow
Aqium® 3D LIGHT packing unit
- REF 82530 2x 50 ml cartridges + 12 Mixing tips NT, yellow
Aqium® 3D MEDIUM
- Working time: 2 min. 15 sec.
- Time in mouth: 2 min. 15 sec.
- Colour: orange
Aqium® 3D MEDIUM packing unit
- REF 82531 2x 50 ml cartridges + 12 Mixing tips NT, yellow
Aqium® 3D MONO
- Working time: 2 min.
- Time in mouth: 2 min.
- Colour: violet
Aqium® 3D MONO packing unit
- REF 85139 2x 380 ml cartridges 5:1
- REF 85199 1x 380 ml cartridge + 10 Mixing tips 5:1, 1 Fix cap
Aqium® accessories
- REF 51291 Fix cap 5:1, yellow, 2 pieces
- REF 51401 Mixing tips 5:1, yellow, 40 pieces
- REF 811511 Mixing tips NT, yellow, 50 pieces
- REF 811513 Mixing tips NT, green, 50 pieces
- REF 474196 Intra-Oral-Tips. yellow, 96 pieces
- REF 811010 Mixing Gun NT (1:1/2:1)
- REF 82005 Mixing Gun (1:1/2:2)
Productdownloads
Advice and contact
Personal advice and contact.
- Formular:To contact form
- E-Mail:info@mueller-omicron.de
- Phone:+49 (0)2266 47420